To install a toilet shut off valve, turn off the water to the house, flush the toilet to empty the tank, disconnect the old supply line and valve, fit the new valve onto the pipe and reconnect the supply line. The part that trips people is the pipe type, because the valve has to match what comes out of the wall. Copper, plastic and flexible stub outs all use different fittings.
If the valve is old and will not turn, replacing it is one of the best small plumbing upgrades you can make. If you would rather hand the job over, our toilet repair service includes new shutoff valves.
Match The FittingIdentify The Pipe Before You Buy The Valve
| Pipe coming from the wall | Typical valve connection | Notes |
|---|---|---|
| Copper stub out | Compression valve | Slides over the pipe and tightens with a nut and sleeve |
| Plastic stub out | Push or compression style | Check that the valve is rated for the pipe type |
| Threaded iron or brass | Threaded valve | Needs thread sealant and care to avoid cracking |
| Soldered copper | Soldered valve | Needs a torch and is better left to a plumber |
Take the old valve to the store if you are unsure. The size printed on the pipe or valve helps, and most toilet supply lines use a three eighths inch fitting at the valve end.
Before You StartTools And Parts
Gather these first
- A new quarter turn shutoff valve that matches the pipe
- A new braided supply line
- Adjustable wrenches or a basin wrench
- A small bucket and a towel
- Thread sealant only if the valve is threaded
The Steps
Shut off the water
Close the main shutoff and open a faucet to relieve pressure.
Empty the tank
Flush the toilet and sponge out what remains.
Remove the old valve
Disconnect the supply line, then loosen the compression nut and slide the valve off.
Install the new one
Slide on the nut and sleeve, seat the valve and tighten until snug.
Reconnect the supply line, turn the water back on slowly and check for drips at the valve and at the line. Tighten a quarter turn at a time and stop when the drip stops. Overtightening can crack the sleeve and cause a new leak.
ProblemWhen The Main Valve Will Not Close
The first step needs a working main shutoff. If the house main will not close or does not hold, do not start the job. A failed main valve is a repair of its own and may point to an older line that needs attention.
Lehi owns the water meter and the valve at the curb. Do not operate the city valve yourself. Call Lehi Water and Sewer at (385) 201-1700 in office hours or 801-836-1045 after hours if you need the city to shut water off.
Know Your LimitsWhen To Call A Plumber
Call a plumber if the pipe is soldered, if the wall is wet around the stub out, or if the pipe moves when you turn the valve. A pipe that is not secured inside the wall can break when you tighten a fitting. Stub out repairs like this are routine work for our crews in Lehi and in American Fork.
If you are chasing a leak that you cannot find, our leak detection service can locate it before any wall is opened. The service areas page lists the towns we serve.
PartsChoosing The Valve And The Supply Line
Shutoff valves come in compression, push fit and soldered styles. Compression valves suit most do it yourself swaps on copper pipe because they need no torch. Quarter turn valves are easier to use than old multi turn valves that seize from lack of use.
Replace the braided supply line when you replace the valve. Old lines can bulge or crack at the ends, and a failed line is a common cause of an indoor flood. Tighten the nut by hand and then snug it with a wrench, since overtightening can damage the washer.
After the swap, open the valve slowly and check every joint with a dry paper towel. Leave the towel in place for a few minutes and look again. Close and open the valve once a year so it does not freeze in place.
Questions about your own house? Call (385) 488-1892 and a person will answer.
FAQsToilet Shutoff Valve Questions
Many people finish in under an hour when the old valve comes off cleanly. A stuck or corroded valve takes longer.
A quarter turn valve closes with a short turn of the handle and tends to last longer. Multi turn valves use a washer that can wear out.
Yes. A braided line is inexpensive, and a new valve with an old line invites a leak.
Call Lehi Water and Sewer at (385) 201-1700 in office hours, or 801-836-1045 after hours.
No. Secure the pipe first, because a loose stub out can break inside the wall when you tighten the fitting.

